U-Boot 2018.05-g24521d6-dirty (Mar 27 2023 - 17:32:51 +0800) Allwinner Technology
[00.312]DRAM: 64 MiB
[00.315]Relocation Offset is: 01ee5000
[00.319]secure enable bit: 0
[00.322]CPU=720 MHz,PLL6=600 Mhz,AHB=200 Mhz, APB1=100Mhz MBus=300Mhz
[00.328]flash init start
[00.331]workmode = 0,storage type = 0
[00.335]sunxi-spinand: AW SPINand MTD Layer Version: 1.5 20200407
[00.340]sunxi-spinand-phy: AW SPINand Phy Layer Version: 1.9 20200306
[00.350]sunxi-spinand-phy: request spi0 gpio ok
[00.354]sunxi-spinand-phy: request general tx dma channel ok!
[00.359]sunxi-spinand-phy: request general rx dma channel ok!
[00.365]sunxi-spinand-phy: set spic0 clk to 20 Mhz
[00.369]sunxi-spinand-phy: init spic0 clk ok
sspi->base_addr = 0x4025000, the SPI control register:
[VER] 0x4025000 = 0x00010001, [GCR] 0x4025004 = 0x00000083, [TCR] 0x4025008 = 0x00000184
[ICR] 0x4025010 = 0x00000f00, [ISR] 0x4025014 = 0x00000032, [FCR] 0x4025018 = 0x00200020
[FSR] 0x402501c = 0x00000000, [WCR] 0x4025020 = 0x00000000, [CCR] 0x4025024 = 0x00000002
[SDC] 0x4025028 = 0x00002000, [BCR] 0x4025030 = 0x00000000, [TCR] 0x4025034 = 0x00000000
[BCC] 0x4025038 = 0x20000000, [DMA] 0x4025088 = 0x000000e5
[00.415]sunxi-spinand-phy: not detect any munufacture from id table
[00.421]sunxi-spinand-phy: get spi-nand Model from fdt fail
[00.427]sunxi-spinand-phy: get phy info from fdt fail
[00.431]sunxi-spinand-phy: not detect munufacture from fdt
[00.437]sunxi-spinand-phy: detect munufacture from id table: Winbond
[00.443]sunxi-spinand-phy: detect spinand id: ff21aaef ffffffff
[00.448]sunxi-spinand-phy: ========== arch info ==========
[00.453]sunxi-spinand-phy: Model: W25N01GVZEIG
[00.459]sunxi-spinand-phy: Munufacture: Winbond
[00.464]sunxi-spinand-phy: DieCntPerChip: 1
[00.468]sunxi-spinand-phy: BlkCntPerDie: 1024
[00.473]sunxi-spinand-phy: PageCntPerBlk: 64
[00.477]sunxi-spinand-phy: SectCntPerPage: 4
[00.482]sunxi-spinand-phy: OobSizePerPage: 64
[00.486]sunxi-spinand-phy: BadBlockFlag: 0x0
[00.491]sunxi-spinand-phy: OperationOpt: 0x7
[00.495]sunxi-spinand-phy: MaxEraseTimes: 65000
[00.500]sunxi-spinand-phy: EccFlag: 0x0
[00.505]sunxi-spinand-phy: EccType: 2
[00.509]sunxi-spinand-phy: EccProtectedType: 3
[00.514]sunxi-spinand-phy: ========================================
[00.520]sunxi-spinand-phy:
[00.522]sunxi-spinand-phy: ========== physical info ==========
[00.528]sunxi-spinand-phy: TotalSize: 128 M
[00.532]sunxi-spinand-phy: SectorSize: 512 B
[00.536]sunxi-spinand-phy: PageSize: 2 K
[00.540]sunxi-spinand-phy: BlockSize: 128 K
[00.544]sunxi-spinand-phy: OOBSize: 64 B
[00.548]sunxi-spinand-phy: ========================================
[00.554]sunxi-spinand-phy:
[00.557]sunxi-spinand-phy: ========== logical info ==========
[00.562]sunxi-spinand-phy: TotalSize: 128 M
[00.566]sunxi-spinand-phy: SectorSize: 512 B
[00.571]sunxi-spinand-phy: PageSize: 4 K
[00.575]sunxi-spinand-phy: BlockSize: 256 K
[00.579]sunxi-spinand-phy: OOBSize: 128 B
[00.583]sunxi-spinand-phy: ========================================
[00.589]sunxi-spinand-phy: set spic0 clk to 100 Mhz
[00.594]sunxi-spinand-phy: block lock register: 0x00
[00.599]sunxi-spinand-phy: feature register: 0x19
[00.603]sunxi-spinand-phy: sunxi physic nand init end
[00.608]mtdparts: mtdparts=nand:1024k@0(boot0)ro,3072k@1048576(uboot)ro,1024k@4194304(secure_storage)ro, -(sys)
device nand0 <nand>, # parts = 4
#: name size offset mask_flags
0: boot0 0x00100000 0x00000000 1
1: uboot 0x00300000 0x00100000 1
2: secure_storage 0x00100000 0x00400000 1
3: sys 0x07b00000 0x00500000 0
active partition: nand0,0 - (boot0) 0x00100000 @ 0x00000000
defaults:
mtdids : nand0=nand
mtdparts: mtdparts=nand:1024k@0(boot0)ro,3072k@1048576(uboot)ro,1024k@4194304(secure_storage)ro,-(sys)
[00.659]MTD info (4)
[00.661]pagesize: 0x1000
[00.663]blksize: 0x40000
[00.665]num offset bytes name
[00.669]0 0x00000000 0x00100000 boot0
[00.672]1 0x00100000 0x00300000 uboot
[00.676]2 0x00400000 0x00100000 secure_storage
[00.680]3 0x00500000 0x07b00000 sys
[00.684]ubi attach the last part of mtd device: NO.3
[00.760]ubi0: attaching mtd4
[00.861]ubi0: scanning is finished
[00.868]ubi0: attached mtd4 (name "sys", size 123 MiB)
[00.872]ubi0: PEB size: 262144 bytes (256 KiB), LEB size: 258048 bytes
[00.879]ubi0: min./max. I/O unit sizes: 4096/4096, sub-page size 2048
[00.885]ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
[00.891]ubi0: good PEBs: 492, bad PEBs: 0, corrupted PEBs: 0
[00.897]ubi0: user volume: 9, internal volumes: 1, max. volumes count: 128
[00.903]ubi0: max/mean erase counter: 2/1, WL threshold: 4096, image sequence number: 0
[00.911]ubi0: available PEBs: 0, total reserved PEBs: 492, PEBs reserved for bad PEB handling: 20
[00.919]sunxi flash init ok
[00.922]line:703 init_clocks
[00.925]init_clocks:finish
[00.928]drv_disp_init
[00.939]get flash lcd idx 0
request pwm success, pwm7:pwm7:0x2000c00.
fdt get node offset faill: hdmi
[00.952]HDMI 2.0 driver init start!
[00.955]fdt_path_offset hdmi fail
[00.958]unable to map hdmi registers
[00.961]drv_disp_init finish
[00.964]boot_gui_init:start
[00.967]set disp.dev2_output_type fail. using defval=0
[00.972]disp 0, clk: pll(525000000),clk(525000000),dclk(75000000) dsi_rate(525000000)
clk real:pll(528000000),clk(528000000),dclk(75428571) dsi_rate(0)
[00.987]switch device: sel=0, type=1, mode=4, format=0, bits=0, eotf=4, cs=260
[00.995]boot_gui_init:finish
[00.997]logical area info: 468 258048 last_lba: 235871
[01.006]logical area info: 468 258048 last_lba: 235871
[01.010]MTD info (4)
[01.012]pagesize: 0x1000
[01.014]blksize: 0x40000
[01.017]num offset bytes name
[01.020]0 0x00000000 0x00100000 boot0
[01.024]1 0x00100000 0x00300000 uboot
[01.027]2 0x00400000 0x00100000 secure_storage
[01.032]3 0x00500000 0x07b00000 sys
[01.036]MBR info (unalign):
[01.038]partno addr sects type name
[01.043]0 0x00000000 0x00008000 0x00000001 mbr
[01.048]1 0x00008000 0x00001b88 0x00008000 boot-resource
[01.053]2 0x00009b88 0x000001f8 0x00008000 env
[01.058]3 0x00009d80 0x000001f8 0x00008000 env-redund
[01.063]4 0x00009f78 0x00005000 0x00008000 boot
[01.068]5 0x0000ef78 0x000103e8 0x00008000 rootfs
[01.073]6 0x0001f360 0x00005780 0x00008000 recovery
[01.078]7 0x00024ae0 0x0000ee20 0x00008000 rootfs_data
[01.084]8 0x00033900 0x00005a90 0x00000000 UDISK
[01.089]ubi attach the last part of mtd device: NO.3
[01.093]MBR info (align):
[01.096]partno addr sects type name
[01.101]0 0x00002800 0x000081f0 0x00000001 mbr
[01.105]1 0x0000a9f0 0x00001b90 0x00008000 boot-resource
[01.111]2 0x0000c580 0x000001f8 0x00008000 env
[01.116]3 0x0000c778 0x000001f8 0x00008000 env-redund
[01.121]4 0x0000c970 0x000050b8 0x00008000 boot
[01.126]5 0x00011a28 0x000105d8 0x00008000 rootfs
[01.131]6 0x00022000 0x00005898 0x00008000 recovery
[01.136]7 0x00027898 0x0000ee38 0x00008000 rootfs_data
[01.142]8 0x000366d0 0x00005a90 0x00000000 UDISK
[01.150]logical area info: 468 258048 last_lba: 235871
[01.159]logical area info: 468 258048 last_lba: 235871
[0[01.169]LCD open finish
1.167]logical area info: 468 258048 last_lba: 235871
[01.179]logical area info: 468 258048 last_lba: 235871
[01.188]logical area info: 468 258048 last_lba: 235871
[01.196]logical area info: 468 258048 last_lba: 235871
[01.205]logical area info: 468 258048 last_lba: 235871
[01.213]logical area info: 468 258048 last_lba: 235871
[01.222]logical area info: 468 258048 last_lba: 235871
[01.230]logical area info: 468 258048 last_lba: 235871
[01.239]logical area info: 468 258048 last_lba: 235871
[01.247]logical area info: 468 258048 last_lba: 235871
[01.255]logical area info: 468 258048 last_lba: 235871
[01.264]logical area info: 468 258048 last_lba: 235871
[01.272]logical area info: 468 258048 last_lba: 235871
[01.281]logical area info: 468 258048 last_lba: 235871
[01.289]logical area info: 468 258048 last_lba: 235871
[01.298]logical area info: 468 258048 last_lba: 235871
[01.306]logical area info: 468 258048 last_lba: 235871
[01.315]logical area info: 468 258048 last_lba: 235871
[01.323]logical area info: 468 258048 last_lba: 235871
[01.332]logical area info: 468 258048 last_lba: 235871
[01.340]logical area info: 468 258048 last_lba: 235871
[01.349]logical area info: 468 258048 last_lba: 235871
[01.357]logical area info: 468 258048 last_lba: 235871
[01.365]logical area info: 468 258048 last_lba: 235871
partno erro : can't find partition bootloader
[01.378]logical area info: 468 258048 last_lba: 235871
[01.386]logical area info: 468 258048 last_lba: 235871
[01.395]logical area info: 468 258048 last_lba: 235871
[01.403]logical area info: 468 258048 last_lba: 235871
[01.412]logical area info: 468 258048 last_lba: 235871
[01.420]logical area info: 468 258048 last_lba: 235871
54 bytes read in 0 ms
[01.427]bmp_name=bootlogo.bmp size 1152056
[01.435]logical area info: 468 258048 last_lba: 235871
[01.443]logical area info: 468 258048 last_lba: 235871
[01.452]logical area info: 468 258048 last_lba: 235871
1152056 bytes read in 56 ms (19.6 MiB/s)
[01.534]logical area info: 468 258048 last_lba: 235871
[01.542]logical area info: 468 258048 last_lba: 235871
[01.551]logical area info: 468 258048 last_lba: 235871
[01.559]logical area info: 468 258048 last_lba: 235871
[01.568]logical area info: 468 258048 last_lba: 235871
[01.576]logical area info: 468 258048 last_lba: 235871
[01.585]logical area info: 468 258048 last_lba: 235871
[01.593]logical area info: 468 258048 last_lba: 235871
[01.602]logical area info: 468 258048 last_lba: 235871
[01.610]logical area info: 468 258048 last_lba: 235871
[01.619]logical area info: 468 258048 last_lba: 235871
[01.627]logical area info: 468 258048 last_lba: 235871
[01.636]logical area info: 468 258048 last_lba: 235871
[01.644]logical area info: 468 258048 last_lba: 235871
[01.653]logical area info: 468 258048 last_lba: 235871
[01.661]logical area info: 468 258048 last_lba: 235871
[01.670]logical area info: 468 258048 last_lba: 235871
[01.678]logical area info: 468 258048 last_lba: 235871
[01.687]logical area info: 468 258048 last_lba: 235871
[01.695]logical area info: 468 258048 last_lba: 235871
[01.704]logical area info: 468 258048 last_lba: 235871
[01.712]logical area info: 468 258048 last_lba: 235871
[01.721]logical area info: 468 258048 last_lba: 235871
[01.729]logical area info: 468 258048 last_lba: 235871
[01.738]logical area info: 468 258048 last_lba: 235871
[01.746]logical area info: 468 258048 last_lba: 235871
[01.755]logical area info: 468 258048 last_lba: 235871
[01.760]Loading Environment from SUNXI_FLASH... OK
[01.784]try to burn key
[01.786]out of usb burn from boot: not need burn key
[01.790]sunxi-spinand: spinand secure storage ok for phy blk 32 and 33
[01.798]Item0 (Map) magic is bad
[01.800]the secure storage map is empty
[01.808]logical area info: 468 258048 last_lba: 235871
[01.816]logical area info: 468 258048 last_lba: 235871
[01.824]logical area info: 468 258048 last_lba: 235871
partno erro : can't find partition private
[01.833]no item name ubi.mtd in the map
[01.836]no item name ubi.block in the map
[01.840]no item name clk_ignore_unused initcall_debugrootfstype in the map
[01.847]no item name rootfstype in the map
[01.850]no item name snum in the map
[01.854]no item name mac in the map
[01.857]no item name wifi_mac in the map
[01.861]no item name bt_mac in the map
[01.864]no item name specialstr in the map
[01.868]root_partition is rootfs
[01.871]nand_root is /dev/ubiblock0_5
[01.874]set root to /dev/ubiblock0_5
[01.878]set aw-ubi-spinand.ubootblks to 24
[01.881]ubi attach the last part of mtd device: NO.3
[01.886]ubi attach the last part of mtd device: NO.3
[01.891]set ubi_attach_mtdnum to 3
[01.894]update ubi part info ok
[01.897]key 0
[01.902]logical area info: 468 258048 last_lba: 235871
[01.910]logical area info: 468 258048 last_lba: 235871
[01.918]logical area info: 468 258048 last_lba: 235871
[01.923]no misc partition is found
[01.926]update bootcmd
[01.932]logical area info: 468 258048 last_lba: 235871
[01.940]logical area info: 468 258048 last_lba: 235871
[01.948]logical area info: 468 258048 last_lba: 235871
[01.953]fdt check ok
[01.955]change working_fdt 0x42aa4da0 to 0x42a84da0
[01.960]replace_fdt success addr:0x42200000
[01.965](weak)update dtb dram start
No reserved memory region found in source FDT
[01.991]update dtb dram end
[01.998]update dts
[01.999]Net: noncached_alloc(): addr = 0x42f2b080
noncached_alloc(): addr = 0x42f2b0c0
noncached_alloc(): addr = 0x42f2b100
noncached_alloc(): addr = 0x42f2b940
geth_sys_init:634: get node 'gmac0' error
geth_sys_init fail!
[02.019]Board Net Initialization Failed
[02.023]No ethernet found.
Hit any key to stop autoboot: 0
[02.034]partinfo: name boot, start 0x9f78, size 0x5000
L
Latest posts made by litengos
-
D1s上电uboot启动过程30%概率卡住，不往下执行posted in D1系列-RISC-V
-
Reply: D1s晶振不起振问题posted in D1系列-RISC-V
@whycan 晶振旁边电容没电压，示波器测没波形。是不是不需要做任何boot 配置，内部有类似与bootloader的程序启动晶振
