@efancier 不发
Posts made by YuzukiTsuru
-
Reply: 求救帖 t1113-s3 mq dual 触摸屏问题 5寸 480X272posted in 全志方案讨论区
试试修改设备树看看是不是那个问题，不过我这里测试这个屏幕没这个问题，不会花
-
Reply: D1-H 使用内置FANOUT REFCLK 24M时钟扫到卡但是无法下载固件posted in D1-H/D1s
@apollo5520 测不到信号就不是这个问题了，加载驱动的时候默认会打开dxco。我那个问题是信号噪音过大的问题
-
Reply: 【极简操作】使用builroot 2021一键编译生成D1 nezha 系统镜像！posted in D1-H/D1s
@mxlol233 更新buildroot 2022.05就ok了
-
Reply: T113 (tina) 如何编译打包spi nand flash 固件posted in 全志方案讨论区
@jr_online
Target Images --->
[*] squashfs --->
-
Reply: 请问XR829 用 24Mhz 和 40Mhz 晶振的时候有什么区别呢？posted in 全志方案讨论区
XR829 使用 40M 晶振与使用 24M 晶振有什么区别
https://bbs.aw-ol.com/topic/1228/share/3
-
Reply: 求救帖 t1113-s3 mq dual 触摸屏问题 5寸 480X272posted in 全志方案讨论区
@a892755772 估计是uboot disp的驱动问题，我之后再看看
-
Reply: 求救帖 t1113-s3 mq dual 触摸屏问题 5寸 480X272posted in 全志方案讨论区
cat /dev/urandom > /dev/fb0 之后屏幕会不会花屏，这里说的花屏是雪花屏不是上面那个还能看出图形的，
cat: write error: No space left on device那个不是报错是正常情况
-
Reply: 求救帖 t1113-s3 mq dual 触摸屏问题 5寸 480X272posted in 全志方案讨论区
@a892755772 这样还是花屏吗
cat /dev/urandom > /dev/fb0
-
Reply: 求救帖 t1113-s3 mq dual 触摸屏问题 5寸 480X272posted in 全志方案讨论区
@a892755772 什么版本？看这个Commit ba93df0b
_____ _____ ___ __ __ _ _ _____ _____ _____ | __ | __ |_ | | | |_ _ ___ _ _| |_|_| __| __ | | | __ -| -| _| |_ _| | |- _| | | '_| |__ | __ -| --| |_____|__|__|___| |_| |___|___|___|_,_|_|_____|_____|_____| Commit: ba93df0b
-
Reply: Porject Yosemite - 基于全志V853的开发板posted in V853
发一个内存模板
测试DDR3 1866没问题，PCB是从LCEDA导出的，JLC打板子选择2313
注意：
- 因格式和图元的设计不一致，格式转换会有一定的差异，导出后请务必在 Altium Designer 仔细检查。
- 导出前请务必阅读： 导出 Altium Designer注意事项与免责声明
- 不承担因导出差异导致的任何生产损失。
-
Reply: Porject Yosemite - 基于全志V853的开发板posted in V853
启动了！内存没啥大问题了
[26182]fes begin commit:fbe7448cdb [26185]set pll start [26187]periph0 has been enabled [26190]set pll end [26193]PMU: AXP21 [26196]board init ok [26198]beign to init dram [26200]DRAM use external ZQ!! [26203]chip id check OK [26206]DRAM_VCC set to 1500 mv [26209]trefi:7.8ms [26211][AUTO DEBUG] single rank and full DQ! [26216]trefi:7.8ms [26218][AUTO DEBUG] rank 0 row = 15 [26222][AUTO DEBUG] rank 0 bank = 8 [26225][AUTO DEBUG] rank 0 page size = 2 KB [26229]DRAM BOOT DRIVE INFO: V0.16 [26232]DRAM CLK = 936 MHz [26235]DRAM Type = 3 (2:DDR2,3:DDR3) [26238]DRAMC ZQ value: 0x7b7bfb [26241]DRAM ODT value: 0x42. [26245]DRAM SIZE =512 M [26247]dram_tpr4:0x0 [26250]DRAM simple test OK. [26253]rtc standby flag is 0x0, super standby flag is 0x0 [26258]init dram ok U-Boot 2018.05-00006-gb5e4c9f6fb (Jun 09 2022 - 06:47:31 +0000) Allwinner Technology [27.808]CPU: Allwinner Family [27.811]Model: sun8iw21 I2C: ready [27.837]DRAM: 512 MiB [27.840]Relocation Offset is: 1ced0000 [27.865]secure enable bit: 0 [27.867]PMU: AXP21 [27.869]PMU: pmu_axp2101 found [27.872]BMU: AXP21 [27.874]BMU: bmu_axp2101 found FDT ERROR:fdt_get_regulator_name:get property handle twi-supply error:FDT_ERR_INTERNAL [27.884]gpio_bias, pc_bias: 1800, pc_supply: not set [27.889]gpio_bias, pl_bias: -1, pl_supply: not set [27.895]dcdc1_vol = 3300, onoff=1 [27.898]dcdc2_vol = 900, onoff=1 [27.901]dcdc5_vol = 0, onoff=0 [27.905]aldo1_vol = 1800, onoff=1 [27.908]aldo2_vol = 1800, onoff=1 [27.912]aldo3_vol = 3300, onoff=1 [27.915]aldo4_vol = 3300, onoff=1 [27.919]bldo1_vol = 1800, onoff=1 [27.922]bldo2_vol = 2800, onoff=1 [27.926]dldo1_vol = 3300, onoff=1 [27.929]dldo2_vol = 1200, onoff=1 bias_name:pc_bias bias_vol:1800 bias_name:pi_bias bias_vol:1800 [27.939]bat_vol=4577, ratio=1 [27.942]safe_vol=3500, safe_ratio=1 [27.946]CPU=900 MHz,PLL6=600 Mhz,AHB=200 Mhz, APB1=24Mhz MBus=300Mhz [27.952]gic: normal mode sunxi flash map init [27.957]flash init start [27.959]workmode = 16,storage type = 0 try card 2 set card number 2 get card number 2 [27.967][mmc]: mmc driver ver uboot2018:2021-12-20 13:35:00 [27.972][mmc]: get sdc_type fail and use default host:tm4. [27.979][mmc]: Is not Boot mode! [27.982][mmc]: SUNXI SDMMC Controller Version:0x50400 [27.993][mmc]: ************Try SD card 2************ [27.998][mmc]: mmc 2 cmd timeout 100 status 100 [28.002][mmc]: smc 2 err, cmd 8, RTO [28.006][mmc]: mmc 2 close bus gating and reset [28.011][mmc]: mmc 2 cmd timeout 100 status 100 [28.015][mmc]: smc 2 err, cmd 55, RTO [28.018][mmc]: mmc 2 close bus gating and reset [28.023][mmc]: ************Try MMC card 2************ [28.079][mmc]: mmc 2 cmd timeout 100 status 100 [28.083][mmc]: smc 2 err, cmd 8, RTO [28.086][mmc]: mmc 2 close bus gating and reset [28.091][mmc]: mmc 2 cmd timeout 100 status 100 [28.095][mmc]: smc 2 err, cmd 55, RTO [28.099][mmc]: mmc 2 close bus gating and reset [28.115][mmc]: gen_tuning_blk_bus8: total blk 10 [28.119][mmc]: gen_tuning_blk_bus4: total blk 6 [28.124][mmc]: Using 8 bit tuning now [28.127][mmc]: send stop [28.129][mmc]: Write tuning pattern failded [28.133][mmc]: Using 8 bit tuning now [28.137][mmc]: send stop [28.139][mmc]: Write tuning pattern failded [28.143][mmc]: Write pattern failed [28.146][mmc]: mmc init product failed MMC init failed try emmc fail [28.153]sunxi-spinand: AW SPINand MTD Layer Version: 1.8 20220106 [28.158]sunxi-spinand-phy: AW SPINand Phy Layer Version: 1.11 20211217 [28.167]sunxi-spinand-phy: request spi0 gpio ok [28.171]sunxi-spinand-phy: request general tx dma channel ok! [28.176]sunxi-spinand-phy: request general rx dma channel ok! [28.182]sunxi-spinand-phy: set spic0 clk to 20 Mhz [28.186]sunxi-spinand-phy: init spic0 clk ok [29.190]sunxi-spinand-phy: read id failed : -110 try nand fail [29.198]unrecognized JEDEC id bytes: ff, ff, ff data abort pc : [<5ff0b602>] lr : [<5ff0b5e9>] reloc pc : [<4303b602>] lr : [<4303b5e9>] sp : 5de6dc38 ip : 0000000c fp : 43000508 r10: 43031ca1 r9 : 5deafe70 r8 : 5deff8a8 r7 : 5ff7f2e8 r6 : ffffffed r5 : 5ff4fbe0 r4 : 5deff8f0 r3 : 00002000 r2 : 00000001 r1 : 0000000a r0 : 00000030 Flags: nZCv IRQs on FIQs off Mode SVC_32
-
Reply: D1-H 2G DDR3 识别问题请教posted in D1-H/D1s
推荐一颗单颗2G的芯片：D9STR，测试可以跑到1866，单帖就OK
或者双贴单颗1G单Die的芯片，D9STQ，测试1600没问题
-
Reply: D1-H 2G DDR3 识别问题请教posted in D1-H/D1s
@apollo5520 内存控制的源码是不开源的，只有二进制发布。DRAM参数设置在sys_config.fex内，libdram会读取这个配置文件所以也不需要调试dram代码。
;sdram configuration另外H5TC8G63CMR是Dual Die Package。意思是一颗内存内其实有2片die，所以一颗内存等于2颗单Die的内存，占用了所有CS线。D1-H 芯片支持双贴单Die的DRAM、同时也支持单帖双Die的DRAM，最大16Gb。
-
Reply: T113奇怪的屏幕刷新问题posted in 全志方案讨论区
@efancier buildroot更新了，修复了i2c，de，uart等一堆问题，source envsetup.sh 更新然后重新make xxxx_defconfig就行了
-
Reply: 求教搭载全志t7的车机内存扩容问题posted in 全志方案讨论区
换成4G内存应该不会启动，两个的地址控制线不太一样。
fel进入模式是可以hook出来的，例如这里的识别到uart即进入fel
-
Reply: D1-H 使用内置FANOUT REFCLK 24M时钟扫到卡但是无法下载固件posted in D1-H/D1s
解决了，示波器测量发现过充，电阻解决
[ 15.077675] ======== XRADIO WIFI OPEN ======== [ 15.086009] [XRADIO] Driver Label:XR_V02.16.85_P2P_HT40_01.31 [ 15.093245] [XRADIO] Allocated hw_priv @ (____ptrval____) [ 15.101203] sunxi-rfkill soc@3000000:rfkill@0: bus_index: 1 [ 15.119168] sunxi-rfkill soc@3000000:rfkill@0: wlan power on success [ 15.289156] FAT-fs (mmcblk0p1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck. [ 15.427605] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B [ 15.439043] [XRADIO] Detect SDIO card 1 [ 15.461469] sunxi-mmc 4021000.sdmmc: no vqmmc,Check if there is regulator [ 15.491817] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 15.525136] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 15.540610] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 15.567424] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing SD-HS(SDR25) dt B [ 15.579332] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 50000000Hz bm PP pm ON vdd 21 width 1 timing SD-HS(SDR25) dt B [ 15.591648] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 50000000Hz bm PP pm ON vdd 21 width 4 timing SD-HS(SDR25) dt B [ 15.605149] mmc2: new high speed SDIO card at address 0001 [ 15.613632] [SBUS] XRadio Device:sdio clk=50000000 [ 15.621530] [XRADIO] XRADIO_HW_REV 1.0 detected. [ 15.772529] [XRADIO] xradio_update_dpllctrl: DPLL_CTRL Sync=0x00c00000. [ 15.927766] [XRADIO] Bootloader complete [ 16.099634] [XRADIO] Firmware completed. [ 16.105809] [WSM] Firmware Label:XR_C09.08.52.73_DBG_02.122 2GHZ HT40 May 18 2021 13:36:09 [ 16.124345] [XRADIO] Firmware Startup Done. [ 16.129480] [XRADIO_WRN] enable Multi-Rx! [ 16.139231] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht' [ 16.169753] xt_time: kernel timezone is -0000
-
Reply: D1-H 使用内置FANOUT REFCLK 24M时钟扫到卡但是无法下载固件posted in D1-H/D1s
正常情况
root@TinaLinux:/lib/modules/5.4.61# insmod xr829.ko ======== XRADIO WIFI OPEN ======== [XRADIO_ERR] debugfs isnot initialized [XRADIO] Driver Label:XR_V02.16.85_P2P_HT40_01.31 [XRADIO] Allocated hw_priv @ 0000000035532399 sunxi-rfkill soc@3000000:rfkill@0: bus_index: 1 sunxi-rfkill soc@3000000:rfkill@0: wlan power on success sunxi-mmc 4021000.sdmmc: sdc set ios:clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B [XRADIO] Detect SDIO card 1 sunxi-mmc 4021000.sdmmc: no vqmmc,Check if there is regulator sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing SD-HS(SDR25) dt B sunxi-mmc 4021000.sdmmc: sdc set ios:clk 50000000Hz bm PP pm ON vdd 21 width 1 timing SD-HS(SDR25) dt B sunxi-mmc 4021000.sdmmc: sdc set ios:clk 50000000Hz bm PP pm ON vdd 21 width 4 timing SD-HS(SDR25) dt B mmc1: new high speed SDIO card at address 0001 [SBUS] XRadio Device:sdio clk=50000000 [XRADIO] XRADIO_HW_REV 1.0 detected. [XRADIO] xradio_update_dpllctrl: DPLL_CTRL Sync=0x00c00000. [XRADIO] Bootloader complete [XRADIO] Firmware completed. [WSM] Firmware Label:XR_C09.08.52.73_DBG_02.122 2GHZ HT40 May 18 2021 13:36:09 [XRADIO] Firmware Startup Done. [XRADIO_WRN] enable Multi-Rx! ieee80211 phy1: Selected rate control algorithm 'minstrel_ht' ···
-
Reply: D1-H 使用内置FANOUT REFCLK 24M时钟扫到卡但是无法下载固件posted in D1-H/D1s
@whycan
找了一个好的板子拆了晶振是这样的root@TinaLinux:/lib/modules/5.4.61# insmod xr829.ko ======== XRADIO WIFI OPEN ======== [XRADIO_ERR] debugfs isnot initialized [XRADIO] Driver Label:XR_V02.16.85_P2P_HT40_01.31 [XRADIO] Allocated hw_priv @ 00000000e2194bdf sunxi-rfkill soc@3000000:rfkill@0: bus_index: 1 sunxi-rfkill soc@3000000:rfkill@0: wlan power on success sunxi-mmc 4021000.sdmmc: sdc set ios:clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B [XRADIO] Detect SDIO card 1 sunxi-mmc 4021000.sdmmc: no vqmmc,Check if there is regulator sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing SD-HS(SDR25) dt B sunxi-mmc 4021000.sdmmc: sdc set ios:clk 50000000Hz bm PP pm ON vdd 21 width 1 timing SD-HS(SDR25) dt B sunxi-mmc 4021000.sdmmc: sdc set ios:clk 50000000Hz bm PP pm ON vdd 21 width 4 timing SD-HS(SDR25) dt B mmc1: new high speed SDIO card at address 0001 [SBUS] XRadio Device:sdio clk=50000000 [XRADIO] XRADIO_HW_REV 1.0 detected. [XRADIO_ERR] xradio_load_firmware: Wait for wakeup:device is not responding. [XRADIO_ERR] Device will restart at 1 times! sunxi-rfkill soc@3000000:rfkill@0: wlan power off success sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 7, RTO !! sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 7, RTO !! sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 7, RTO !! sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 7, RTO !! mmc1: card 0001 removed sunxi-mmc 4021000.sdmmc: sdc set ios:clk 0Hz bm PP pm OFF vdd 0 width 1 timing LEGACY(SDR12) dt B [XRADIO] Remove SDIO card 1 sunxi-mmc 4021000.sdmmc: sdc set ios:clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B sunxi-mmc 4021000.sdmmc: no vqmmc,Check if there is regulator sunxi-rfkill soc@3000000:rfkill@0: bus_index: 1 sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B sunxi-rfkill soc@3000000:rfkill@0: wlan power on success sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing SD-HS(SDR25) dt B sunxi-mmc 4021000.sdmmc: sdc set ios:clk 50000000Hz bm PP pm ON vdd 21 width 1 timing SD-HS(SDR25) dt B sunxi-mmc 4021000.sdmmc: sdc set ios:clk 50000000Hz bm PP pm ON vdd 21 width 4 timing SD-HS(SDR25) dt B mmc1: new high speed SDIO card at address 0001 [XRADIO] Detect SDIO card 1 [SBUS] XRadio Device:sdio clk=50000000 [XRADIO] XRADIO_HW_REV 1.0 detected. [XRADIO_ERR] xradio_load_firmware: Wait for wakeup:device is not responding. [XRADIO_ERR] Device will restart at 2 times! sunxi-rfkill soc@3000000:rfkill@0: wlan power off success sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 7, RTO !! sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 7, RTO !! sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 7, RTO !! sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 7, RTO !! mmc1: card 0001 removed sunxi-mmc 4021000.sdmmc: sdc set ios:clk 0Hz bm PP pm OFF vdd 0 width 1 timing LEGACY(SDR12) dt B [XRADIO] Remove SDIO card 1 sunxi-mmc 4021000.sdmmc: sdc set ios:clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B sunxi-mmc 4021000.sdmmc: no vqmmc,Check if there is regulator sunxi-rfkill soc@3000000:rfkill@0: bus_index: 1 sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B sunxi-rfkill soc@3000000:rfkill@0: wlan power on success sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing SD-HS(SDR25) dt B sunxi-mmc 4021000.sdmmc: sdc set ios:clk 50000000Hz bm PP pm ON vdd 21 width 1 timing SD-HS(SDR25) dt B sunxi-mmc 4021000.sdmmc: sdc set ios:clk 50000000Hz bm PP pm ON vdd 21 width 4 timing SD-HS(SDR25) dt B mmc1: new high speed SDIO card at address 0001 [XRADIO] Detect SDIO card 1 [SBUS] XRadio Device:sdio clk=50000000 [XRADIO] XRADIO_HW_REV 1.0 detected. [XRADIO_ERR] xradio_load_firmware: Wait for wakeup:device is not responding. [XRADIO_ERR] Device will restart at 3 times! sunxi-rfkill soc@3000000:rfkill@0: wlan power off success sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 7, RTO !! sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 7, RTO !! sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 7, RTO !! sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 7, RTO !! mmc1: card 0001 removed sunxi-mmc 4021000.sdmmc: sdc set ios:clk 0Hz bm PP pm OFF vdd 0 width 1 timing LEGACY(SDR12) dt B [XRADIO] Remove SDIO card 1 sunxi-mmc 4021000.sdmmc: sdc set ios:clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B sunxi-mmc 4021000.sdmmc: no vqmmc,Check if there is regulator sunxi-rfkill soc@3000000:rfkill@0: bus_index: 1 sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B sunxi-rfkill soc@3000000:rfkill@0: wlan power on success sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing SD-HS(SDR25) dt B sunxi-mmc 4021000.sdmmc: sdc set ios:clk 50000000Hz bm PP pm ON vdd 21 width 1 timing SD-HS(SDR25) dt B sunxi-mmc 4021000.sdmmc: sdc set ios:clk 50000000Hz bm PP pm ON vdd 21 width 4 timing SD-HS(SDR25) dt B mmc1: new high speed SDIO card at address 0001 [XRADIO] Detect SDIO card 1 [SBUS] XRadio Device:sdio clk=50000000 [XRADIO] XRADIO_HW_REV 1.0 detected. ^C[XRADIO_ERR] xradio_load_firmware: Wait for wakeup:device is not responding. [XRADIO_ERR] Device will restart at 4 times! sunxi-rfkill soc@3000000:rfkill@0: wlan power off success sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 7, RTO !! sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 7, RTO !! [XRADIO] Remove SDIO card 1 sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 7, RTO !! sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 7, RTO !! mmc1: card 0001 removed sunxi-mmc 4021000.sdmmc: sdc set ios:clk 0Hz bm PP pm OFF vdd 0 width 1 timing LEGACY(SDR12) dt B sunxi-mmc 4021000.sdmmc: sdc set ios:clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B sunxi-mmc 4021000.sdmmc: no vqmmc,Check if there is regulator sunxi-rfkill soc@3000000:rfkill@0: bus_index: 1 sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B sunxi-rfkill soc@3000000:rfkill@0: wlan power on success sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing SD-HS(SDR25) dt B sunxi-mmc 4021000.sdmmc: sdc set ios:clk 50000000Hz bm PP pm ON vdd 21 width 1 timing SD-HS(SDR25) dt B sunxi-mmc 4021000.sdmmc: sdc set ios:clk 50000000Hz bm PP pm ON vdd 21 width 4 timing SD-HS(SDR25) dt B mmc1: new high speed SDIO card at address 0001 [XRADIO] Detect SDIO card 1 [SBUS] XRadio Device:sdio clk=50000000 [XRADIO_ERR] xradio_register_bh failed(-4). sunxi-rfkill soc@3000000:rfkill@0: wlan power off success sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 7, RTO !! sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 7, RTO !! [XRADIO] Remove SDIO card 1 sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 7, RTO !! sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 7, RTO !! mmc1: card 0001 removed sunxi-mmc 4021000.sdmmc: sdc set ios:clk 0Hz bm PP pm OFF vdd 0 width 1 timing LEGACY(SDR12) dt B ^Csunxi-mmc 4021000.sdmmc: sdc set ios:clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B sunxi-mmc 4021000.sdmmc: no vqmmc,Check if there is regulator xradio_core_init failed (-4)! sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 52, RTO !! sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 52, RTO !! sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 5, RTO !! sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 5, RTO !! sunxi-mmc 4021000.sdmmc: smc 1 p1 err, cmd 5, RTO !!
-
Reply: D1-H 使用内置FANOUT REFCLK 24M时钟扫到卡但是无法下载固件posted in D1-H/D1s
@whycan
降速了好像也没有用io绑错了
[ 19.052197] ======== XRADIO WIFI OPEN ======== [ 19.057744] [XRADIO] Driver Label:XR_V02.16.85_P2P_HT40_01.31 [ 19.064598] [XRADIO] Allocated hw_priv @ (____ptrval____) [ 19.072289] sunxi-rfkill soc@3000000:rfkill@0: bus_index: 1 [ 19.097764] sunxi-rfkill soc@3000000:rfkill@0: wlan power on success [ 19.307190] sunxi_hosts[1] should not be null [ 19.307197] [XRADIO] Detect SDIO card 1 [ 21.361925] sunxi-rfkill soc@3000000:rfkill@0: wlan power off success [ 21.469153] sunxi_hosts[1] should not be null [ 21.469161] [XRADIO] Remove SDIO card 1 [ 21.488339] [SBUS_ERR] sdio probe timeout! [ 21.492954] [XRADIO_ERR] sbus_sdio_init failed [ 21.499076] xradio_core_init failed (-110)!
-
Reply: 小麻雀直接驱动树莓派的DSI屏posted in D1-H/D1s
@daming123 brandy-2.0/u-boot-2018/configs/sun20iw1p1_defconfig 注释掉 #CONFIG_DISP2_SUNXI=y，使用kernel初始化屏幕测试
-
Reply: D1-H 使用内置FANOUT REFCLK 24M时钟扫到卡但是无法下载固件posted in D1-H/D1s
量了一下好像内置REFCLK_OUT没有输出，但是我这个探头电容很大，可能会导致这个问题
-
D1-H 使用内置FANOUT REFCLK 24M时钟扫到卡但是无法下载固件posted in D1-H/D1s
[ 15.763263][ 15.763263] ======== XRADIO WIFI OPEN ======== [ 15.770569][ 15.770569] [XRADIO] Driver Label:XR_V02.16.85_P2P_HT40_01.31 [ 15.779230][ 15.779230] [XRADIO] Allocated hw_priv @ (____ptrval____) [ 15.788116][ 15.788116] sunxi-rfkill soc@3000000:rfkill@0: bus_index: 1 [ 15.806534][ 15.806534] sunxi-rfkill soc@3000000:rfkill@0: wlan power on success [ 16.158083][ 16.158083] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B [ 16.170922][ 16.170922] [XRADIO] Detect SDIO card 1 [ 16.181998][ 16.181998] sunxi-mmc 4021000.sdmmc: no vqmmc,Check if there is regulator [ 16.209670][ 16.209670] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 16.233815][ 16.233815] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 16.252653][ 16.252653] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 16.279628][ 16.279628] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing SD-HS(SDR25) dt B [ 16.293081][ 16.293081] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 50000000Hz bm PP pm ON vdd 21 width 1 timing SD-HS(SDR25) dt B [ 16.306785][ 16.306785] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 50000000Hz bm PP pm ON vdd 21 width 4 timing SD-HS(SDR25) dt B [ 16.324944][ 16.324944] mmc2: new high speed SDIO card at address 0001 [ 16.343747][ 16.343747] [SBUS] XRadio Device:sdio clk=50000000 [ 16.360502][ 16.360502] [XRADIO] XRADIO_HW_REV 1.0 detected. [ 16.483883][ 16.483883] [XRADIO] xradio_update_dpllctrl: DPLL_CTRL Sync=0x00c00000. [ 16.593457][ 16.593457] [XRADIO] Bootloader complete [ 17.138413][ 17.138413] FAT-fs (mmcblk0p1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck. [ 17.571269][ 17.571269] [XRADIO_ERR] xradio_firmware: wait for download completion failed. Read: 0xFFFFFFFF [ 17.594485][ 17.594485] [XRADIO_ERR] xradio_load_firmware: can't download firmware. [ 17.603764][ 17.603764] [XRADIO_ERR] xradio_load_firmware failed(-110). [ 17.613037][ 17.613037] sunxi-rfkill soc@3000000:rfkill@0: wlan power off success [ 17.748248][ 17.748248] sunxi-mmc 4021000.sdmmc: smc 2 p1 err, cmd 7, RTO !! [ 17.756403][ 17.756403] sunxi-mmc 4021000.sdmmc: smc 2 p1 err, cmd 7, RTO !! [ 17.764552][ 17.764552] sunxi-mmc 4021000.sdmmc: smc 2 p1 err, cmd 7, RTO !! [ 17.772665][ 17.772665] sunxi-mmc 4021000.sdmmc: smc 2 p1 err, cmd 7, RTO !! [ 17.781030][ 17.781030] mmc2: card 0001 removed [ 17.786530][ 17.786530] [XRADIO] Remove SDIO card 1 [ 17.792516][ 17.792516] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 0Hz bm PP pm OFF vdd 0 width 1 timing LEGACY(SDR12) dt B [ 17.828132][ 17.828132] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B [ 17.849201][ 17.849201] sunxi-mmc 4021000.sdmmc: no vqmmc,Check if there is regulator [ 17.859197][ 17.859197] xradio_core_init failed (-110)! [ 17.878141][ 17.878141] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 17.904007][ 17.904007] sunxi-mmc 4021000.sdmmc: smc 2 p1 err, cmd 52, RTO !! [ 17.913008][ 17.913008] sunxi-mmc 4021000.sdmmc: smc 2 p1 err, cmd 52, RTO !! [ 17.921267][ 17.921267] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 17.937887][ 17.937887] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 17.953800][ 17.953800] sunxi-mmc 4021000.sdmmc: smc 2 p1 err, cmd 5, RTO !! [ 17.963051][ 17.963051] sunxi-mmc 4021000.sdmmc: smc 2 p1 err, cmd 5, RTO !! [ 17.972010][ 17.972010] sunxi-mmc 4021000.sdmmc: smc 2 p1 err, cmd 5, RTO !! [ 17.980988][ 17.980988] sunxi-mmc 4021000.sdmmc: smc 2 p1 err, cmd 5, RTO !! [ 17.989171][ 17.989171] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 0Hz bm PP pm OFF vdd 0 width 1 timing LEGACY(SDR12) dt B [ 18.009905][ 18.009905] xt_time: kernel timezone is -0000 [ 18.032430][ 18.032430] Error: Driver 'gt9xxnew_ts' is already registered, aborting... [ 19.788243][ 19.788243] ======== XRADIO WIFI OPEN ======== [ 19.795187][ 19.795187] [XRADIO] Driver Label:XR_V02.16.85_P2P_HT40_01.31 [ 19.803393][ 19.803393] [XRADIO] Allocated hw_priv @ (____ptrval____) [ 19.813200][ 19.813200] sunxi-rfkill soc@3000000:rfkill@0: bus_index: 1 [ 19.840210][ 19.840210] sunxi-rfkill soc@3000000:rfkill@0: wlan power on success [ 20.050260][ 20.050260] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B [ 20.062758][ 20.062758] [XRADIO] Detect SDIO card 1 [ 20.073213][ 20.073213] sunxi-mmc 4021000.sdmmc: no vqmmc,Check if there is regulator [ 20.093157][ 20.093157] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 20.119383][ 20.119383] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 20.135394][ 20.135394] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 20.159295][ 20.159295] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing SD-HS(SDR25) dt B [ 20.172219][ 20.172219] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 50000000Hz bm PP pm ON vdd 21 width 1 timing SD-HS(SDR25) dt B [ 20.185470][ 20.185470] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 50000000Hz bm PP pm ON vdd 21 width 4 timing SD-HS(SDR25) dt B [ 20.199392][ 20.199392] mmc2: new high speed SDIO card at address 0001 [ 20.207730][ 20.207730] [SBUS] XRadio Device:sdio clk=50000000 [ 20.223252][ 20.223252] [XRADIO] XRADIO_HW_REV 1.0 detected. [ 20.273703][ 20.273703] [XRADIO] xradio_update_dpllctrl: DPLL_CTRL Sync=0x00c00000. [ 20.315910][ 20.315910] [XRADIO] Bootloader complete [ 21.014043][ 21.014043] [XRADIO_ERR] xradio_firmware: wait for download completion failed. Read: 0xFFFFFFFF [ 21.025220][ 21.025220] [XRADIO_ERR] xradio_load_firmware: can't download firmware. [ 21.034002][ 21.034002] [XRADIO_ERR] xradio_load_firmware failed(-110). [ 21.042814][ 21.042814] sunxi-rfkill soc@3000000:rfkill@0: wlan power off success [ 21.163655][ 21.163655] sunxi-mmc 4021000.sdmmc: smc 2 p1 err, cmd 7, RTO !! [ 21.171759][ 21.171759] [XRADIO] Remove SDIO card 1 [ 21.171775][ 21.171775] sunxi-mmc 4021000.sdmmc: smc 2 p1 err, cmd 7, RTO !! [ 21.185540][ 21.185540] sunxi-mmc 4021000.sdmmc: smc 2 p1 err, cmd 7, RTO !! [ 21.193670][ 21.193670] sunxi-mmc 4021000.sdmmc: smc 2 p1 err, cmd 7, RTO !! [ 21.202023][ 21.202023] mmc2: card 0001 removed [ 21.213388][ 21.213388] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 0Hz bm PP pm OFF vdd 0 width 1 timing LEGACY(SDR12) dt B [ 21.231535][ 21.231535] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 0Hz bm PP pm UP vdd 21 width 1 timing LEGACY(SDR12) dt B [ 21.244107][ 21.244107] sunxi-mmc 4021000.sdmmc: no vqmmc,Check if there is regulator [ 21.254279][ 21.254279] xradio_core_init failed (-110)! [ 21.263169][ 21.263169] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 21.299296][ 21.299296] sunxi-mmc 4021000.sdmmc: smc 2 p1 err, cmd 52, RTO !! [ 21.308775][ 21.308775] sunxi-mmc 4021000.sdmmc: smc 2 p1 err, cmd 52, RTO !! [ 21.317076][ 21.317076] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B kmodloader done [ 21.377217][ 21.377217] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 400000Hz bm PP pm ON vdd 21 width 1 timing LEGACY(SDR12) dt B [ 21.405391][ 21.405391] sunxi-mmc 4021000.sdmmc: smc 2 p1 err, cmd 5, RTO !! [ 21.414360][ 21.414360] sunxi-mmc 4021000.sdmmc: smc 2 p1 err, cmd 5, RTO !! [ 21.423298][ 21.423298] sunxi-mmc 4021000.sdmmc: smc 2 p1 err, cmd 5, RTO !! [ 21.432228][ 21.432228] sunxi-mmc 4021000.sdmmc: smc 2 p1 err, cmd 5, RTO !! [ 21.440382][ 21.440382] sunxi-mmc 4021000.sdmmc: sdc set ios:clk 0Hz bm PP pm OFF vdd 0 width 1 timing LEGACY(SDR12) dt B
-
Reply: 为了摆脱TINA-BSP的磁盘噩梦能舒服地只编译LVGL8在D1S/D1上面肆意玩耍posted in D1-H/D1s
@jr_online d1s是riscv，t113是arm a7，怎么可能改个名字就行
-
Reply: 【Yuzuki手作】D1s-Nezha开发板全全开源上架（内含购买链接和全部软硬件资料）posted in D1-H/D1s
@fengshulin make kernel_menuconfig 里关闭xradio lpm
-
Reply: 【Yuzuki手作】D1s-Nezha开发板全全开源上架（内含购买链接和全部软硬件资料）posted in D1-H/D1s
│ Prompt: bash.......................................... The GNU Bourne Again SHell │ │ Location: │ │ -> Utilities │ │ (6) -> Shells
-
Reply: 【Yuzuki手作】D1s-Nezha开发板全全开源上架（内含购买链接和全部软硬件资料）posted in D1-H/D1s
@fengshulin m menuconfig 查找 bash 把他关闭就行了，我自己适配了bash，下载的不适配
-
Reply: 有D1S/F133连接以太网的参考吗posted in D1-H/D1s
参考一下这个，千兆网：
Yuzuki RV Router RISC-V 旁路由
https://bbs.aw-ol.com/topic/1583/share/3
-
Yuzuki RV Router RISC-V 旁路由posted in D1-H/D1s
- 千兆以太网
- 2lane MIPI DSI 屏幕
- 支持CTP
- 1 USB 2.0 HOST
- 1 USB OTG、POWER
- XR829 Wi-Fi & BT
-
Tina 增加一个 Package 将交叉编译好的 bin 打包进去posted in Linux
在Package文件夹下新建文件夹 my_lvgl
目录结构. ├── bin │ ├── lib │ │ ├── kksk.so # 动态库 │ │ ├── libglog.so # 动态库 │ │ └── lvgl_1.so # 动态库 │ └── my_lvgl # my_lvgl 主程序 └── Makefile # 下面的Makefileinclude $(TOPDIR)/rules.mk include $(INCLUDE_DIR)/package.mk PKG_NAME:=my_lvgl PKG_VERSION:=1.0.0 PKG_RELEASE:=1 PKG_BUILD_DIR := $(BUILD_DIR)/$(PKG_NAME) SRC_CODE_DIR := ./bin define Package/$(PKG_NAME) SECTION:=My Package CATEGORY:=My LVGL DEPENDS:=+libc +libstdcpp + TITLE:=My LVGL endef # 这里放一些外部的库 define Package/$(PKG_NAME)/extra_provides echo 'libstdc++.so.6' && echo 'libc.so' endef define Package/$(PKG_NAME)/config # 留空 endef define Package/$(PKG_NAME)/Default # 留空 endef define Package/$(PKG_NAME)/description My LVGL endef define Build/Prepare $(INSTALL_DIR) $(PKG_BUILD_DIR)/ $(CP) -rf $(SRC_CODE_DIR)/* $(PKG_BUILD_DIR)/ endef define Build/Configure # 留空 endef define Build/Compile # 留空 endef #define Build/InstallDev # 留空 #endef define Package/$(PKG_NAME)/install $(INSTALL_DIR) $(1)/usr/bin/ $(INSTALL_BIN) $(PKG_BUILD_DIR)/my_lvgl $(1)/usr/bin/ $(INSTALL_DIR) $(1)/usr/lib/ $(INSTALL_BIN) $(PKG_BUILD_DIR)/lib/lib* $(1)/usr/lib/ endef $(eval $(call BuildPackage,$(PKG_NAME)))
-
Reply: xfel烧录不了32M nor flashposted in 编译和烧写问题专区
sunxi-fel烧写没问题
sudo sunxi-fel -p spiflash-write 0 flashimg.bin 100% [================================================] 33554 kB, 3045.6 kB/s SF: Detected mx25l25635f with page size 256 Bytes, erase size 64 KiB, total 32 MiB
-
Reply: 这个目录下的sample是怎么编译的posted in 编译和烧写问题专区
make menuconfig到mpp里找一下sample，勾选上需要的sample再编译试试看，勾选了的才会编译
-
Reply: 【开源直播】手把手教你用全志XR32芯片DIY一个自己的开发板（二：PCB焊接调试）posted in XR32
@lifanko 或者试一下 VBAT 也给3.3V看看还是不是4V以上
-
Reply: 【开源直播】手把手教你用全志XR32芯片DIY一个自己的开发板（二：PCB焊接调试）posted in XR32
@lifanko 倒是没有什么额外条件，主要是3V3电压是4V就说明芯片没有正常工作
可以在立创那边参考一下：https://oshwhub.com/GloomyGhost/yuzukixr32f4
-
Reply: OpenixCard - 在 Linux 系统刷写全志镜像到 SD 卡posted in 编译和烧写问题专区
更新了1.0.2版本
_____ _ _____ _ | |___ ___ ___|_|_ _| |___ ___ _| | | | | . | -_| | |_'_| --| .'| _| . | |_____| _|___|_|_|_|_,_|_____|__,|_| |___| |_| Copyright (c) 2022, YuzukiTsuru <GloomyGhost@GloomyGhost.com> Usage: OpenixCard [options] Optional arguments: -h --help shows help message and exits [default: false] -v --version prints version information and exits [default: false] -u --unpack Unpack Allwinner Image to folder [default: false] -d --dump Convert Allwinner image to regular image [default: false] -c --cfg Get Allwinner image partition table cfg file [default: false] -p --pack Pack dumped Allwinner image to regular image from folder [default: false] -i --input Input Allwinner image file or dumped image directory [required] eg. OpenixCard - TUI Interface -> NOT AVALIABLE OpenixCard -u -i <img> - Unpack Allwinner image to target OpenixCard -u -c -i <img> - Unpack Allwinner image to target and generate Allwinner image partition table cfg OpenixCard -d -i <img> - Convert Allwinner image to regular image OpenixCard -p -i <dir> - Pack dumped Allwinner image to regular image from folder
